Products not found
The LinkIQ Network+Cable Tester is the trusted cable and network testing solution for validating and troubleshooting cable performance from 10BASE-T to 10GBASE-T (10 Mb/s up to 10Gb/s). LinkIQ supports Industrial Ethernet (EtherNet/IP, PROFINET, EtherCAT, and others).
price by request
The DSX CableAnalyzer works on cables running EtherNet/IP, Profnet, ModBus TCP, EtherCAT, plus other protocols. It offers touchscreen project management, TIA Level IIIe accuracy, and advanced troubleshooting, all with integrated Wi-Fi and 8-hour battery life.
The kit includes the Versiv mainframe and remote units, a reference module, adapters, commonly used accessories, and a statement of calibration.
price by request
The Pro3000 unfiltered toner, for use on inactive networks, uses SmartTone technology, with five different tones to allow the technician to easily identify individual pairs. Angled-bed-of-nails clips allow easy access to individual wires, and the RJ11 connector is ideal for use on telephone jacks.
price by request
The Pro3000 unfiltered tone generator, for use on inactive networks, uses SmartTone technology, with five different tones to allow the technician to easily identify individual pairs and sends signal up to 10 miles. Alligator clips attach to wires and and RJ11 plug connects to telephone jacks.
price by request
The Pro3000 unfiltered probe, for use on inactive networks, features a loud speaker to hear tone clearly through walls, enclosures and in loud environments. The recessed on/off button helps prevent the probe from accidently being turned on when stored.
price by request
Fluke Networks Cable fault finder with PowerBT Bridge Tap Detect provides open/short circuit detection—to 8,000 feet (2.4 km) and locates multiple bridge taps up to 3,200 feet (975 m) of cable, built-in toner has five tones, reports AC/DC voltage on any two conductor, telephone, security wires, or coax cables.
price by request
The Pro3000F filtered probe, 60 Hz, “Stops the Buzz” by obstructing signal interference (caused by power cables and lightning) present in the environment when listening for tone. The probe’s powerful speaker makes tracing cables through drywall, wood or other enclosures quick and easy.
price by request
MT-8200-63A Probe detects IntelliTone digital signals on active networks and 500 to 1,200 Hz analog signals on inactive networks to locate, trace, and isolate copper cabling
price by request
Digital and analog tone generator verifies and troubleshoots copper cabling in networks—identifying the type of service and verifying continuity. F-type connector supports VDV cables: RJ45, RJ11, coaxial, bare wire, banana jacks/test leads. Diagnoses 10/100 Gigabit Ethernet link connectivity with NIC/hub indication.
price by request
The MicroMapper MT-8200-49A is a hand-held cable tester that makes it easy to verify the integrity of Ethernet twisted pair cables. Test for opens, shorts, reversed, crossed, and split pairs and scan for any existing faults in your cable. Trace cables hidden in ceilings, walls, floors, and bundles.
price by request
The Fluke Networks MicroScanner 2 Industrial Ethernet Cable Verifier performs continuity tests on RJ45, M12X, M12D, and M8D terminated cables in seconds and displays results graphically so you can see opens, shorts, and crossed wires.
price by request
The MicroScanner 2 Cable Verifier helps find common errors quickly, displaying results from what were four different test modes all at once on its oversized, backlit LCD display: graphical wire map, pair lengths, distance to fault, cable ID, and far-end device. Its integrated RJ11, RJ45, and coax test ports support virtually any type of low-voltage cable testing, with no need for awkward adapters.
price by request
The Fluke Networks MicroScanner PoE Industrial Ethernet Cable Verifier performs continuity tests on RJ45, M12X, M12D, and M8D terminated cables in a few seconds and displays results graphically so you can see opens, shorts, and crossed wires.
price by request
The tester detects the available PoE class (0-8) in accordance to the latest PoE standards and displays the voltage from passive PoE sources. Everything cable technicians need to know, including available services (up to 10G Ethernet), cable length, wiremap, cable ID, and distance to fault are all shown on the LCD screen.
price by request
The LinkIQ Cable+Wi-Fi+Network Tester is the testing solution to verify cable performance up to 10 Gb/s and solve network connectivity problems. The LinkIQ tester validates cable performance using frequency-based measurements and a wire map of the cable under test.
price by request
The LinkIQ Industrial Ethernet Cable+Wi-Fi+Network Tester is the testing solution to verify cable performance up to 10 Gb/s and solve network connectivity problems. The LinkIQ tester validates cable performance using frequency-based measurements and a wire map of the cable under test.
price by request